No products in the cart.
Assembly Machines
GW INSTEK
Showing 1–15 of 27 results
-
Function Generator
AFG-3000 Series Arbitrary Function Generator
Features
- Wide frequency range from 1uHz to 80/50MHz
- High 200MSa/s sampling rate
- 16-bit Amplitude Resolution
- Output from any section of 1M-point-long waveform
- 4.3″ high-resolution LCD display/on-screen help/Impedance switch
- Four ways to generate arbitrary waveform: Front Panel Operation
- CSV file uploading, Direct Waveform Reconstruction (DWR), Arbitrary
- Waveform Editing PC Software
- USB, RS-232, GPIB interface support
SKU: n/a -
Digital Meters
GDM-8351 Digital Meters / Digital Multimeters
Features
- 120,000 counts, VFD display
- Dual measurement/Dual display
- The basic precision of DC voltage: 0.012%
- Selectable measurement speeds, the maximum: 320 Readings/s
- True RMS (AC，AC+DC) measurements
- Auto/manual selection
- 12 different measurement functions: AC/DC voltage, AC/DC current, AC+DC voltage/current, 2W/4W resistance, continuity beeper, diode test, capacitance, frequency, temperature
- Many auxiliary functions: Max./Min., REL/REL#, Compare, Hold, dB, dBm, Math (MX+B, %, 1/X)
- Digital I/O provides dual mode (standard Compare and User definition modes)
- Standard RS-232C and USB device interface (support USBCDC and USBTMC modes)
SKU: GDM-8351 -
Digital Meters
GDM-9061 Digital Meters / Digital Multimeters
Features
- 6 1/2 Digit Display:1,200,000 Counts
- 4.3 TFT Craphic LCD
- DCV Basic Accuracy:0.0035%(GDM-9061)/0.0075%(GDM-9060)
- 12 Measurement Functions: DCV, ACV, DCI, ACI, 2-wire and 4-wire Resistance, Frequency, Period, Diode, Continuity, Temperature and Capacitance
- Sampling Rate up to 10k SPS (GDM-9061)
- Dual Measurement Function to Providing Two Selected Measurement Simultaneously
- Offer Graphical Capabilities lncluding Histogram, Bar Meter and Trend
- Temperature Measurement Support RTD, Thermistor as Well as Thermocouple
- Standard Interfaces: USB Host/Device, RS-232C, LAN, Digital I/O
- Optional Interface: GPIB
SKU: GDM-9061 -
Oscilloscope
GDS-2000A Gwinstek Digital Storage Oscilloscopes
GDS-2000A Gwinstek Digital Storage Oscilloscopes Features
- 300MHz/200MHz/100MHz/70MHz Bandwidth ,2 or 4 Input Channel
- 2GSa/s Real-time Sampling Rate and 100GSa/s Equivalent Time Sampling Rate
- 2Mega Points Record Length
- 1mV /div to 10V/div of Vertical Range
- 1ns/div to 100s/div of Time Base Range
- 80,000 wfm/s of Waveform Update Rate
- 8 inch 800*600 High Resolution TFT LCD Display
- Built-in Segmented Memory and Waveform Search Functions to Optimize the Efficiency of Record Length
- Zoom Window and Play/Pause can Rapidly Navigate the Waveforms
- 36 Automatic Measurement Functions Offers Various Measurement Selections
- Optional 8 or 16 digital channel with Logic analyzer(MSO)
- Optional Function Generator
- Flexible Remote Control Connectivity(Standard:USB ;Option:LAN/GPIB)
- Upgradable CAN/LIN bus analysis ,Advanced Logic ,Datalog ,DVM and H-expansion functionalities
SKU: GDS-2304A -
Oscilloscope
GDS-3000 Gwinstek Digital Storage Oscilloscopes
GDS-3000 Gwinstek Digital Storage Oscilloscopes Features
- 500/350/250/150MHz with 2/4 Channels
- 5GSa/s RT or 100GSa/s ET Sampling Rate
- Independent Memory for Each Channel
- VPO Technology
- Large 8-inch 800×600 Display
- Split Screen Function
- 3 Built-in Impedances (50Ω/75Ω/1MΩ)
- Power Analysis Software (Optional)
- Serial Bus Analysis Software for I2C, SPI and UART (Optional)
SKU: GDS-3502 -
Digital Meters
GOM-804 & GOM-805 DC Milli-Ohm Meters
Features
- 50,000 counts
- 3.5” (320 x 240) TFT LCD display
- High accuracy of 0.05% precision
- 1Amp test current, 0.1µΩ resolution
- Fast measurement of 60 readings per second
- Four wire resistance measurement
- Temperature compensation measurement function
- Delayed measurement
- 20 sets of panel setting memory
- Dry circuit (GOM-805 only)
- Drive modes (GOM-805) : DC+/DC-, Pulsed, PWM, Zero, Standby
- Drive modes (GOM-804) : DC+, Standby
- Interface: USB device, RS-232C, Handler/Scan/EXT I/O, and GPIB (option)
SKU: n/a -
non-programmable and multiple channel DC power supplies
GPE-x323 Series (Linear)
Features
- 1 / 2 / 3 / 4 Independent Isolated Output
- 4.3 Inch LCD Display
- Setting & Read back Resolution 100mV / 10mA (*1)
- Output ON/OFF
- Analog Control (Remote I/O) for Output ON / OFF
- Set View function for checking an original V / I setting during output on
- Key Lock Function
- Tracking series and parallel operation
- Smart cooling fan achieving low noise
- Optional European Jack Type Terminal
SKU: n/a -
Digital Meters
GPM-8213 AC Power Meters
Features
- 4” TFT LCD
- Two data display modes
- Standard : two major measurement items + six secondary measurement items
- Simple : displaying test data of four different measurement items
- Met the requirement of IEC 62301 power measurement
- Voltage/ current test frequency bandwidth : DC~6kHz
- Watt resolution : 1mW
- Lowest current range : 5mA, resolution : 0.1uA
- Current/voltage measurements reach CF=3 for distorted wave and CF=6 for half range
- W-h (power vs time)/A-h (current vs time) integration function
- Total harmonic distortion measurement
- Front panel test terminal
- Standard interface : RS-232C, USB device, LAN
- Optional interface : GPIB
- Optional test fixture : GPM-001
SKU: n/a -
Programmable and multiple channel DC power supplies
GPP- Series
Features
- 4.3”TFT LCD Display
- Supports Setting Value, Measurement Value and Output Waveform Display
- Load Function (CC, CV, CR Mode)
- Setting Resolution: 1mV / 0.1mA; Read Back Resolution: 0.1mV / 0.1mA
- Low Ripple Noise: ≦350uVrms/ ≦2mArms
- Transient Response Time: ≦50uS
- Utilizing Hardware to Realize Over Voltage Protection / Over Current Protection / Over Temperature Protection
- Delay Function / Output Monitoring Function / Output Recorder Function
- Intelligent Temperature Control Fan Effectively Reduces Noise
- Sequential Output Function and Built-in 8 Template Waveforms
- The Output Recorder Function Records The Output Voltage & Current Parameters with A Minimum Recording Interval of 1 Second.
- Provides 10 Sets of Memory for Each Sequence/Delay/Recorder/Panel Setting Condition
- GPP-3323 Supports A USB (Type A) Output Terminal
- Standard: RS-232, USB, Ext I/O ; Optional: LAN, GPIB+LAN
- Compatible with Commands of GPD-x303S Series
SKU: n/a -
non-programmable and multiple channel DC power supplies
GPS-Series (Linear)
Features
- Light and Compact Design
- 0.01% High Regulation
- Constant Voltage and Constant Current Operation
- Remote Control for External Programmability
- Internal Select for Continuous or Dynamic Load
- Low Ripple and Noise
- Overload and Reverse Polarity Protection
- Series or Parallel Operation
- Optional European Type Jack Terminal for GPS-3030/GPS-3030D/GPS-3030DD
SKU: n/a -
Digital Meters
GPT-9800 Safety Testers (Hi-Pot Tester)
Features
- 200VA AC Test Capacity
- 240×64 Ice Blue Dot matrix LCD
- Manual/Auto Mode
- Function Key for quick selecting
- High intensity flash for Caution & Status indication
- Safety INTERLOCK function
- Zero Crossing Turn-on Operation
- Controllable Ramp-up Time
- True RMS Current Measurement
- High resolution: 1uA for measuring current, 2V for setting voltage
- PWM amplifier to enhance the power efficiency and reliable testing
- Max. 100 memory block for test condition (step) setting. And each step can be named individually.
- Remote terminal on the front panel for “start” and “stop” control
- Interface : RS-232C, USB device, Signal I/O and GPIB (optional)
SKU: GPT-9804 -
Spectrum Analyzer
GSP-9330 Spectrum Analyzer
Features
- Frequency Range: 9kHz ~ 3.25GHz
- 0.025ppm Frequency Stability and 1ppm aging Rate
- RBW: 1Hz ~ 1MHz (3dB), 6dB EMI Filter: 200Hz, 9kHz, 120kHz, 1MHz
- Fastest sweep time: 204us
- Sensitivity: -149 dBm/Hz (@PreAmp on)
- Built-in Preamplifier, 50dB Attenuator, and Sequence Function
- Built-in EMC pretest function, Quasi-Peak/Average EMI detect mode
- Built-in 2FSK Analysis, AM/FM/ASK/FSK Demodulation & Analysis
- Built-in P1dB point, Harmonic, CHPW, OCBW, ACPR, SEM, TOI, CNR, CTB, CSO, N-dB bandwidth, Noise Marker, Frequency Counter, TDP, Gated Sweep
- Built-in Spectrogram, Topographic and Split-Window Display Modes
- Remote control EMI measurement software: SpectrumShot
- Remote Control Interface: LAN, USB, RS-232
- Options: Tracking Generator, GPIB Interface, Battery Pack
SKU: GSP-9330 -
Digital Meters
LCR-6000 – LCR Meters
Features
- 3.5” color LCD
- 5 models (10Hz~2kHz/20kHz/100kHz/200kHz/300kHz)
- Consecutive test frequency
- Basic accuracy : 0.05%
- Measuring speed up to 25ms (max.)
- Full frequency range or spot OPEN/SHORT
- 16 major/secondary parameter measurement combinations and two additional monitoring parameters(maximum four different parameters can be shown simultaneously)
- DCR measurement and internal D.C. bias voltage (±2.5V)
- PASS/FAIL judgment
- Auto Level Control (ALC) function
- BIN function provides 9BIN and 1AUX, totally 10 BIN
- 10 steps listed tests to select different frequency, voltage and current criteria
- Standard interface : RS-232C, Handler and USB storage
- Compact size, ideal for automatic equipment (2U,1/2 RACK)
SKU: n/a -
Digital Meters
LCR-8000G – LCR Meters
Features
- Wide Test Frequency 20Hz ~ 10/5/1MHz
- 0.1% Basic Accuracy & 6 Digits Measurement Resolution
- Large LCD Display with Intuitive Interface
- Full Measuring Functions with DUT V/I Monitor
- PASS/FAIL Function ( abs, % or delta) with Judgment Alarm
- DC Resistance Measurement
- Multiple Step Mode
- Standard RS-232C/GPIB Interface
- Optional DC Bias box
SKU: n/a
